Korg i3 – power rail repair

Views: 928

I bought a Korg i3 – broken – from ebay, the seller claimed it just stopped working. If that is true, usually the power rail is to blame. And in most cases it’s a dead capacitor. No big deal – usually.

The first board to come out is KLM-1631:

And a check on the components showed me that something let the magic smoke out – LC1. And it was right at the connector to the power supply:

The power supply looked good, so I assumed this was the culprit.

According to the Service manual, LC1 is a DST310, a component I hadn’t seen before, but I had guessed right, a blown capacitor.

I don’t have these and couldn’t find a source – maybe these aren’t produced anymore? But it’s just a power filter, I could probably get away with just connecting CN8A-5 directly to the “A” point. But having capacitive storage in a power rail is always a good thing. And since I’m already in there, I can do at least a decent job.

So I desoldered this LC1, cleaned the board and had to find the traces were eaten away. I additionally removed C92 as these capacitors were just in parallel. Also, maybe C92 was damaged by some surge – it was in the way and costs next to nothing. Only to find out that the trace going to C92 had left us as well.

So, if in doubt – scream and shout. Uhm… these are buffer capacitors, so they just sit between plus and minus, both traces were large enough to just scratch the solder screen off and solder in capacitors. Again, I could probably have gotten away with just one, but the original schematic had two, so I used two:

Yep, it’s ugly. Yep, I probably should have used a ceramic for the smaller one, but seriously, it is the 5V rail, quite likely this is the supply for the logic and won’t have any effect on the sound.

Starting up, it works:

So, I was right to assume a blasted capacitor in the power rail was to blame.

But, as Dr. House kept reminding us: people lie.

Next up: Repairing Power-On-Mute on an i3.

Korg C-35 Concert Piano Fehleranalyse

Views: 1465

Vor kurzem erstand ich ein E-Piano von Korg, Typ C-35 Concert Piano. Die Beschreibung bei ebay lässt sich einfach zusammen fassen: Ton sehr leise, aber lautes Knarzen in den Lautsprechern.

Eine kurze Suche im Internet ergab, dass es sich um einen öfter vorkommenden Fehler handeln dürfte, bei dem der Mixerteil des Logik-/Vorverstärker-/Mischerboards stirbt, weil Kondensatoren auslaufen.

In der Hoffnung, dass nur dies auch hier der Fall ist, kaufte ich das E-Piano. Zum Öffnen mussten hinten links und rechts je 2 Schrauben geöffnet werden und unten links und rechts je 3. Der Deckel kann dann – noch gehalten von 2 Scharnieren – nach hinten geklappt werden. Zum Vorschein kamen die 2 Platinen, wovon die rechte für die Stromversorgung und die Endstufe und die linke für die Tonerzeugung und Vorverstärkung zuständig ist. Das Logikboard versteckt sich unter einer Metallfolie. Folie und Platine sind mit einer guten Menge an Schrauben fest gehalten. Nachdem alle Schrauben und Steckverbinder gelöst waren, konnte ich mir das Board genauer ansehen. Einer der vielen Kondensatoren, die sich im Mixerbereich knubbeln, war tatsächlich ausgelaufen. Das Elektrolyt hat bereits 2 Leitbahnen zerstört.

Sobald ich die Ruhe habe, werde ich den ausgelaufenen Kondensator entfernen, die Platine reinigen und die zerstörten Leiterbahnen überbrücken. Und wenn ich schon dabei bin, werden alle etwa 20 Kondensatoren gegen neue getauscht, damit das Problem nicht so schnell wieder auftaucht.